一、进口气动隔膜调节阀概述
进口气动隔膜调节阀,Pneumatic diaphragm control valve,也叫进口气动调节型隔膜阀,美国威盾VTON品牌,是由多弹簧气动薄膜执行器与隔膜调节阀阀体组成,接收4-20Ma或者1-5v信号,对介质(比如氯气,腐蚀、剧毒气体或者高粘度及悬浮颗粒流体)的流量,温度,和压力进行自动化调节的隔膜调节阀。
Pneumatic diaphragm control valve, also known as imported pneumatic regulating diaphragm valve, is an American brand VTON. It is composed of a multi spring pneumatic diaphragm actuator and a diaphragm regulating valve body, receiving 4-20Ma or 1-5V signals to automatically regulate the flow rate, temperature, and pressure of media (such as chlorine gas, corrosive, highly toxic gases, or high viscosity and suspended particle fluids).
气动隔膜调节阀具有结构简单、流路阻小、流通力较同口径的其它阀大,无泄漏,能用于高粘度及悬浮颗粒流体的调节,根据隔膜材料的不同(橡胶或聚四氟乙烯)适用于调节强碱、强腐蚀性介质。由隔膜阀配用气动薄膜执行机构组成。隔膜与阀体间“山”形凸出面进行密封,与外界隔离(无填料函),气动隔膜调节阀特别适合于要求耐腐蚀、剧毒场合。气动隔膜调节阀采用模块化设计,可采用不同组合、配用各种附件。
Pneumatic diaphragm control valve has a simple structure, small flow resistance, larger flow force than other valves of the same caliber, no leakage, and can be used for regulating high viscosity and suspended particle fluids. Depending on the diaphragm material (rubber or polytetrafluoroethylene), it is suitable for regulating strong alkaline and corrosive media. Composed of a diaphragm valve equipped with a pneumatic diaphragm actuator. The "mountain" shaped protruding surface between the diaphragm and valve body is sealed to isolate from the outside (without a packing box). Pneumatic diaphragm control valves are particularly suitable for environments that require corrosion resistance and high toxicity. The pneumatic diaphragm control valve adopts a modular design and can be equipped with various accessories in different combinations.
三、进口气动隔膜调节阀技术参数
公称通径:DN15-250 | 公称压力:1.6Mpa-6.4Mpa | |
允许压差:1.0-0.09 | 配用执行器型号:VPA/B-22、VPA/B-23、VPA/B-34、VPA/B-45 | |
流量系数(KV):8-1800 | 阀盖形式:标准型(-17~+250℃) | |
适用介质:水、油品、气体 | 连接方式:法兰、螺纹、焊接 | |
额定行程(mm):10、16、25、40、60、100 | 阀芯形式:隔膜式 | |
密封填料:V型聚四氟乙烯填料、含浸聚四氟乙烯石棉填料、石棉纺织填料、石墨填料 | 压盖形式:螺栓压紧式 | |
阀座直径:20-300 | 流量特性:快开特性 |
四、进口气动隔膜调节阀气动执行器
配置执行器类别:VPA/B多弹簧簿膜执行机构 | 执行器型号:VPA/B-22、VPA/B-23、VPA/B-34、VPA/B-45 | |
有效面积(cm2):350-1400 | 弹簧范围(KPa):20~100(标准)、20-60、60-100、40-200、80-240 | |
膜片材料:丁腈橡胶夹尼龙布、乙丙橡胶夹尼龙布 | 供气压力:140~400KPa | |
气源接口:RC1/4" | 环境温度:-30~+70℃ | |
可配附件:定位器、空气过滤减压器、保位阀、行程开关、阀位传送器、手轮机构等 | 作用形式:气关式(B)—失气时阀位开(FO);气开式(K)—失气时阀位关(FC) |
五、进口气动隔膜调节阀性能指标
项目 | 指标值 | |
基本误差% | 不带定位器(±5.0)、带定位器(±1.0) | |
回差% | 不带定位器(3.0)、带定位器(1.0) | |
死区% | 不带定位器(3.0)、带定位器(0.4) | |
额定行程偏差% | ±2.5 | |
泄露量L/h | 0.01%×阀额定容量 | |
可调范围R | 30:1 |
六、进口气动隔膜调节阀零件材料
零件 | 材料 | |
阀体 | HT200、ZG230~450或下述材质衬里 | |
隔膜 | 丁荃胶、天然胶、聚四氟乙烯波纹 | |
薄膜 | 丁腈橡胶夹增强涤纶织物 | |
弹簧 | 60S12Mn、阀体衬里材质及适用范围 |
七、进口气动隔膜调节阀阀体衬里材料适用场合
阀体衬里 | 使用温度(℃) | 适用介质 |
无衬里 | -10~+175 | 适用于非腐蚀性介质 |
软橡胶 | -10~+85 | 有很好的耐磨性能,适用于水泥、粘土、煤尘、干燥化肥等 |
硬橡胶 | -10~+85 | 适用于无机械、盐类、盐酸、镀金属溶液、软水、氯化物、氯气等 |
氯丁胶 | -10~+105 | 适用于动物油、植物油和润滑油,PH值变化范围很大的腐蚀性泥浆。抗磨损性能良好 |
丁荃胶 | -10~+120 | 防腐性能和耐磨性能良好,对大部分无机酸和酸性灰浆的耐蚀性最好 |
搪瓷 | -10~+175 | 适用于温无机酸、氧化酸、卤素、醇类、酯类等化合物 |
氟46 | -10~+190 | 适用于硫酸、盐酸、氢氧化钠等强腐蚀介质 |
八、进口气动隔膜调节阀外形尺寸
公称通径 | 外形安装尺寸 | ||||
A | H | H1 | L | ||
VMAT型 | ZMBT型 | ||||
15 | 280 | 479 | 532 | 47.5 | 140 |
20 | 479 | 532 | 52.5 | 145 | |
25 | 479 | 532 | 57.5 | 155 | |
32 | 325 | 538 | 617 | 67.5 | 165 |
40 | 553 | 632 | 72.5 | 190 | |
50 | 562 | 641 | 80 | 210 | |
65 | 410 | 754 | 855 | 90 | 240 |
80 | 100% | 876 | 97.5 | 270 | |
100 | 857 | 958 | 107.5 | 335 |
九、进口气动隔膜调节阀分析图纸
关注我们
微信联系
Copyright © 2013-2023 All Rights Reserved. 粤ICP备17016233号